About Radio laser
Notice For New Zealand Notice for New Zealand For modem with approval number PTC 211/03/008 The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Page 94: Important Safety Instructions This device is equipped with pulse dialing while the Telecom standard is DTMF tone dialing. There is no guarantee that Telecom lines will always continue to support pulse dialing. Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Page 95 If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. Page 96: Laser Compliance Statement Laser compliance statement The CD or DVD drive used with this computer is a laser product. The CD or DVD drive's classification label (shown below) is located on the drive. CLASS 1 LASER PRODUCT CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. Page 97: Radio Device Regulatory Notice Radio device regulatory notice Note: Below regulatory information is for models with wireless LAN and/or Bluetooth only. General This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules). Page
Key features of the Radio laser that are enabled through these drivers include:
- 80s Pirate Radio Laser 558 - YouTube
- HS Code - laser-equipped vehicle radios
- The Laser story - part one - offshore radio
- Radio Laser, 92.4 FM, Pisticci, Italy
- Is there such a thing as a radio laser ? If so, how does it
- Laser FM en vivo - radios-uruguay.com
- Is there such a thing as a radio laser ? If so, how does it work?
Or other similar surface. This shelf system should not be placed in a built-ininstallation such as a bookcase or rack unless correct ventilation is provided or theseinstructions have been adhered to.Laser warningWARNING: This shelf system uses a laser system.To ensure correct use of this shelf system, read this user guide carefully and retainit for future reference. Should your shelf system require maintenance, contact anauthorized service center.Changing controls, making adjustments, or carrying out procedures other than thosespecified herein may result in hazardous radiation exposure.To prevent direct exposure to the laser beam, do not try to open the enclosure.There is visible laser radiation when open.Do not stare into the beam.Laser Type: Dual semiconductor laser GaAIAsWavelength: 650nm and 780nmOutput Power: 7mW1. Standby indicator Power on/off Mode - No Light; Standby Mode - Red LED.Beam Divergence: 60 degree2. Infrared receiver Receives the signal from the remote control.3. LCD Display Area Displays status messages.CAUTION: Visible and invisible laser radiation is present when your shelf system isopen and interlocks are defeated.4. Disc Tray Place a DVD or CD, label side up, into this tray.5. iPod dock Insert your iPod player into this jack.Power Cord6. VOLUME Adjusts the volume. Turn clockwise to increase the volume andCAUTION:It is recommend that most appliances be placed on a dedicated circuit—counter-clockwise to decrease the volume.a single outlet circuit powering that appliance only and has no additional outlets7. STANDBY/ON Press to turn your shelf system on or to standby mode.or branch circuits. Check the specification section of this guide for power8. Phones Plug standard headphones into this jack.requirements.9. AUX IN Plug external device with Audio output into this jack to play its soundDo not overload wall outlets. Overloaded wall outlets, loose or damaged wallthrough this player.outlets, extension cords, frayed power cords, or damaged or cracked wire insulation10.CHANNEL 1) Disc/USB mode - a. Skips to previous chapter or track,are dangerous. Any of these conditions could result in electric shock or fire.b. Press and hold to fast backward. 2) Radio mode - Tune to previous radioPeriodically examine your shelf system cord, and if its appearance indicateschannel memory. 3) Standby mode - When adjusting clock setting, press todamage or deterioration, unplug it, discontinue use of your shelf system, and havedecrease an hour/minute.the cord replaced with an exact replacement part by an authorized service provider.11.CHANNEL 1) Disc/USB mode - a. Skips to next chapter or track, b. PressProtect the power cord from physical or mechanical abuse, such as being twisted,and hold to fast forward 2) Radio mode - Tune to next radio channel memory.kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs,3) Standby mode - When adjusting the clock setting, press to increase an hour/wall outlets, and the point where the
